HVAC & Plumbing Services in Kansas City, MO

Completed installation of a 50-gallon electric water heater with thermal expansion tank and ball valve shut-off in basement utility area. Installed secondary electrical disconnect box with proper conduit routing to provide code-compliant power shutoff for the water heater circuit. All copper supply lines, electrical connections, and safety components were properly secured and tested for operation.

Responded to emergency recall for sump pump failure with water discharge issue. Upon arrival, found disconnected discharge piping at PVC coupling connection, causing water to spray from the apparatus. Customer had unplugged the unit to stop the discharge, resulting in pit refilling. Inspected the 16-year-old system and identified failed connection components. Replaced defective coupling and flexible connectors with new rubber connectors and secured with metal band clamps. Reassembled discharge piping, tested system operation, and verified proper water evacuation with no leaks at connection points.

Responded to a clogged kitchen drain in a 20-year-old residential property. Upon arrival, assessed the under-sink plumbing assembly which included a red garbage disposal unit with white PVC trap and drain lines. The sink basin showed significant debris accumulation around the brass drain fitting, indicating blockage in the drainage system. Performed diagnostic inspection of the disposal unit and connected drain lines to identify the source of the clog. Cleared the obstruction from the kitchen sink drain line, removing accumulated food particles, grease buildup, and debris that had restricted water flow. Tested the garbage disposal for proper operation and verified electrical connections were secure. Flushed the drain system thoroughly to ensure complete removal of blockage and confirmed proper drainage flow. Inspected all PVC connections, trap assembly, and mounting hardware for leaks or deterioration. Cleaned the sink basin and drain area, removing residual debris. System restored t

Responded to report of toilet leaking at rubber seal in main bathroom. Upon inspection, found severely deteriorated wax ring and flange seal with significant water damage and discoloration around the toilet base and floor flange. Removed and reset toilet, replaced failed wax ring with new seal, and reinstalled unit with proper compression to ensure watertight connection. Verified water supply line connections and tested for leaks upon completion.

Completed plumbing maintenance inspection of water heater and pressure tank system. Inspected all copper piping connections, brass fittings, pressure relief valve configuration, and pressure gauge at T-fitting junction, confirming proper installation and operation of both the water heater unit and blue pressure tank with associated plumbing components.

Performed annual maintenance inspection on electric heat pump water heater located in basement mechanical space. Conducted comprehensive system evaluation including visual inspection of unit, electrical connections, plumbing connections, pressure relief valve, and condensate drainage system. Verified proper operation of all heating elements and heat pump components. Inspected copper supply lines and brass fittings for signs of corrosion or leakage. Tested temperature and pressure relief valve functionality. Checked electrical cord and connections for damage or wear. Examined PVC condensate drain line routing and verified proper drainage. No deficiencies, leaks, or operational issues identified during inspection. Unit operating within normal parameters with all safety systems functioning correctly.

Completed toilet installation in residential bathroom. Installed new white toilet unit with proper mounting and sealing to tiled floor. Note: Toilet seat may require replacement or adjustment to ensure correct fit and model compatibility with installed fixture.

Responded to service call for outdoor faucet assembly experiencing movement and instability issues following installation. Upon inspection, found water spigot with green wheel handle valve, brass valve body, black Y-connector splitter, and quick-connect adapter mounted at brick-to-siding junction. Assessed mounting concerns where vinyl shutter material was inadequate for securing pipe assembly to exterior wall substrate. Evaluated proper anchoring requirements for brick surface to eliminate movement and ensure secure permanent installation of outdoor water supply fixture.

Conducted on-site evaluation for gas line installation from existing residential natural gas meter to heated pool location. Assessed current gas meter assembly with corroded copper piping connections, measured required piping distance across backyard to pool area, and documented active construction zone with exposed plumbing infrastructure. Provided comprehensive estimate for gas line extension including materials, trenching requirements, and connection specifications to supply adequate BTU capacity for pool heating system.

Responded to service call for locked-up In-Sinkerator garbage disposal unit under kitchen sink. Upon inspection, identified jamming issue potentially caused by foreign object (small "S" hook) that may have fallen into disposal chamber. Accessed disposal unit from cabinet beneath sink, cleared obstruction, and tested unit operation to ensure proper functionality. Verified all plumbing connections, P-trap configuration, and electrical connections were secure and operating correctly. Disposal unit restored to normal working condition with no leaks detected.

Installed a new 50-gallon gas water heater in the basement utility area, connecting copper supply lines with shut-off valves and proper insulation. The unit was positioned on a stable platform with gas line connection featuring a yellow shut-off valve for safety compliance. All plumbing connections were secured and tested to ensure proper operation of the residential water heating system.

Responded to service call for faucet replacement and evaluation of outdoor valve system. Successfully replaced a warranty-covered faucet fixture, completing full installation with new braided stainless steel flex supply lines connected to existing chrome shutoff valves. Verified proper connections at sink basin, ensured secure mounting of all plumbing components, and tested system for leaks. Provided quote for replacement of two exterior hose bibs as requested. All connections sealed properly with no water leakage detected upon completion.

Successfully installed a complete sump pump system in designated closet location, including Watchdog primary pump with battery backup combo unit and WiFi monitoring capability. Jackhammered and removed concrete flooring, excavated to proper depth, and installed new sump basin with primary and backup pump assembly. Completed all discharge piping and check valve connections with proper routing to exterior of home. Removed and hauled away all concrete debris, excavated soil, and construction materials from work area. Tested system for proper pump activation, discharge flow, and alarm functionality to ensure full operational readiness.

Responded to callback for newly installed sump pump running continuously without water present in pit. Upon inspection, identified faulty float switch mechanism causing pump to remain activated. Adjusted float switch positioning and verified proper operation through multiple water level cycles to ensure automatic on/off functionality restored.

Completed installation of customer-supplied toilet in bathroom. Removed existing fixture and installed new two-piece toilet with wax ring seal to ensure proper connection to the waste flange. Connected chrome water supply line from wall shut-off valve to toilet tank fill valve, verified all connections for proper seal and function, and tested for leaks. Toilet is operational and ready for use.

Completed plumbing inspection of water heater installation and under-sink supply line connections. Documented existing copper piping, pressure vessel with securing bands, brass fittings, and flexible supply lines with shut-off valves in proper working condition.

Responded to report of continuously running toilet in main bathroom. Upon inspection, found faulty flapper valve causing water to leak from tank into bowl, preventing fill valve from shutting off properly. Removed tank lid and assessed internal components. Replaced worn pink flapper valve and adjusted chain length to ensure proper seal over flush valve opening. Tested flush mechanism multiple times to verify flapper seats correctly and water flow stops completely after tank refills. Toilet now functioning properly with no continuous running.

Responded to water leak from shower hot and cold supply lines in basement. Upon inspection, identified significant corrosion and deterioration at pipe penetration points through ceiling surface. Repaired leaking shower supply lines, addressed corroded pipe connections, and secured proper sealing at fixture stub-out to prevent further water intrusion.

Responded to service call for Rinnai tankless water heater experiencing intermittent temperature maintenance issues and displaying error code 12 (low gas pressure/flow detection). Unit required weekly manual resets to restore operation. Upon inspection, diagnosed faulty flame rod sensor causing erratic gas valve operation and false low-gas readings. Removed and replaced defective flame rod assembly with OEM Rinnai component. Verified proper sensor positioning and electrical connectivity. Tested unit through multiple heating cycles to confirm consistent temperature output and proper gas valve modulation. System now operating within manufacturer specifications with no error codes present.

Completed plumbing maintenance inspection and service call addressing tankless flush system components and associated water supply connections. Inspected and verified proper operation of shut-off valves, flexible supply lines with braided metal construction, and PVC drainage piping throughout the installation, ensuring all connections were secure and functioning within normal parameters.