HVAC & Plumbing Services in Kansas City, MO

Conducted initial site assessment for comprehensive sewer line replacement project. Evaluated existing clay tile piping from residence to municipal connection point and assessed cast iron piping running approximately 10 feet from main stack to building exterior. Documented current conditions of basement living space and crawl space infrastructure, including exposed spray foam insulation, existing plumbing lines, and HVAC ductwork to prepare estimate for complete pipe replacement and camera scope inspection of sewer system.

Completed installation of control board, control panel, and temperature/pressure relief pipe on tankless water heater system. Replaced failed control board with new unit, secured all electrical connections including multi-colored wiring harnesses, and installed proper relief piping with code-compliant discharge termination. Verified all brass valves, pressure gauges, and safety devices are functioning correctly, tested system operation, and confirmed unit is heating properly with no error codes displayed.

Responded to low water pressure complaint on third floor shower. Inspected Imperial brand shower valve assembly and thermostatic mixing valve to diagnose cause of reduced flow. Removed valve cover plates to examine internal brass components, cartridge mechanism, and water supply connections for blockages, debris, or mechanical failure. Documented condition of shower control system and thermostatic temperature regulator. Provided recommendations to customer for improving water pressure, which may include cartridge replacement, pressure balancing valve adjustment, or addressing supply line restrictions affecting third floor fixtures.

Performed hydro-jetting service on sewer line as requested. Located and accessed the cleanout point in the lawn area near the concrete walkway. Deployed high-pressure water jetting equipment to clear the line and restore proper flow. Documented pre-service conditions with exterior site photography and conducted camera inspection of the line interior, revealing buildup and debris at approximately 149 feet into the system. Successfully cleared blockage and verified line functionality upon completion.

Responded to service call for sump pump reported as not operating correctly in basement. Upon inspection, verified existing sump pump functionality and assessed discharge line routing from basement to exterior. Confirmed discharge line was properly positioned and draining away from foundation, with hose extending across concrete walkway into landscaped area. System tested and operating within normal parameters at time of service completion.

Responded to service call for leak under kitchen sink. Upon arrival, conducted thorough inspection of cabinet interior and plumbing connections. Located source of moisture at supply line connection point beneath sink basin. Identified loose compression fitting on cold water supply line allowing water seepage. Tightened compression nut to manufacturer specifications using appropriate wrenches. Inspected additional plumbing connections including P-trap assembly and hot water supply line for potential issues. Verified all connections were secure and properly sealed. Cycled water supply on and off multiple times while monitoring for any signs of leakage. Confirmed repair was successful with no visible moisture or dripping present. Documented conditions with photographs for service records. Left work area clean and dry with all plumbing fixtures functioning properly.

Responded to service call for leaking faucet installation issue. Upon arrival, found homeowner had attempted to replace kitchen faucet but encountered installation difficulties resulting in active leak. Assessed the Moen faucet assembly and identified improper connection of supply lines and mounting hardware. Disassembled the partially installed fixture, verified all components were present and undamaged, then proceeded with correct installation following manufacturer specifications. Properly secured mounting hardware beneath sink, connected hot and cold water supply lines with appropriate torque, and installed pull-down sprayer assembly. Tested faucet operation including spray function, checked all connections for leaks, and confirmed proper water flow and temperature control. Installation completed successfully with no leaks detected.

Responded to emergency water leak in kitchen caused by failed copper supply line connecting sink to refrigerator ice maker. Upon arrival, located active leak at corroded pipe fitting and successfully shut off water supply at main valve. Removed deteriorated copper pipe assembly showing significant oxidation and corrosion at multiple connection points, particularly at the brass junction fitting. Replaced entire compromised section with new copper piping and fittings, ensuring proper connections and testing all joints for leaks before restoring water service.

Responded to reported leak from top of tankless water heater unit in basement. Upon inspection, identified leak originating from pressure relief valve and associated plumbing connections. Tightened brass fittings, inspected internal components and pipe connections, and verified proper sealing of all mounting hardware. Unit tested and confirmed no further leakage present upon completion.

Replaced existing water heater with new 40-gallon gas water heater in basement with walk-out access. Installation included connecting copper supply lines, installing expansion tank with pressure gauge, configuring gas line with flexible connector, and establishing proper venting through existing ductwork. All plumbing connections were secured with appropriate valves and fittings, pressure relief valve installed per code requirements, and system tested for proper operation and leak-free performance.

Responded to kitchen sink drain stoppage in 37-year-old residence with basement access. Upon arrival, confirmed clog location previously identified by homeowner and assessed that proper drain clearing equipment would be required. Accessed drain system from basement, utilizing professional drain auger to clear obstruction from kitchen sink line. Successfully removed blockage and restored full drainage flow. Tested system operation with water flow to verify complete clearance and proper drainage function. Inspected under-sink plumbing connections, garbage disposal unit (model E101), P-trap assembly, and supply line shut-off valves to ensure no secondary issues or leaks present. All components functioning properly upon completion.

Removed and reset toilet to address reported seal issue. Pulled toilet from floor flange, removed old wax ring, and inspected flange for damage. Installed new wax ring seal and properly repositioned toilet, ensuring secure mounting and proper alignment with drain opening. Verified leak-free operation upon completion.

Completed comprehensive plumbing inspection of residential property. Evaluated interior shower system, confirming proper water flow and functionality of chrome handheld shower fixture with wall-mounted components. Inspected exterior water service connection and verified water pressure readings using calibrated gauge, which displayed normal operating pressure within acceptable range. All plumbing systems inspected were found to be in functional working condition with no immediate repairs required.

Responded to callback for water pressure issues at bathroom sink faucet where cartridge had been previously installed. Upon arrival, inspected the widespread bathroom faucet with brushed nickel finish mounted on granite countertop. Tested water flow from both hot and cold handles and evaluated cartridge operation. Verified proper installation and function of faucet components. Documented existing conditions with photos showing faucet assembly and sink basin from multiple angles for service records.

Completed site assessment for water meter relocation project. The existing meter is located in the outdoor landscaped area near a large tree with exposed root system and adjacent to concrete walkway with utility access points. Documented current meter positioning relative to tree roots, concrete pavers, sidewalk sections, and existing underground utility infrastructure to determine optimal relocation path and new meter placement that will provide adequate accessibility while avoiding conflicts with tree root systems and established hardscape features.

Responded to reported leak originating from upstairs bathroom tub/shower area. Upon inspection, confirmed leak source was tub drain assembly, which ceased when fixture use was discontinued. Assessed affected area below and verified no structural damage, ceiling sagging, or electrical hazards present. Additionally addressed bathroom sink pop-up stopper assembly that had become disconnected and required reinstallation and adjustment. Inspected water heater and noted missing discharge pipe on temperature and pressure relief valve, which requires code-compliant installation for safety purposes.

Responded to service call for multiple plumbing and fixture issues in residential bathroom. Corrected improperly installed shower valve that had been placed in backwards orientation, restoring proper hot/cold water function. Repaired and secured water heater flue connection to ensure proper venting and safety compliance. Secured loose bathroom vanity to wall, eliminating movement and potential water damage. Inspected and addressed drainage concerns in shower/tub area to ensure proper water flow and prevent future backup issues.

Responded to a drain cleaning service call at a second-floor bathroom. Successfully cleared the clogged drain in the vanity sink, restoring proper water flow and drainage. The fixture was tested and confirmed to be functioning normally upon completion.

Responded to service call for ADA-compliant toilet and sink assessment in main bathroom. Upon arrival, performed thorough inspection of existing fixtures to evaluate options for achieving ADA height requirements. Examined plumbing connections, supply lines, and drain configuration to determine feasibility of replacement versus modification. Documented current installation with photographs showing water supply valve condition, noting corrosion on copper tubing that would require attention during any fixture replacement. Provided comprehensive estimate detailing costs for installing ADA-height toilet and sink fixtures, including necessary plumbing modifications and updated supply line connections to meet accessibility standards.

Responded to service call for pressurized toilet that would not stop flushing in bathroom. Upon inspection, diagnosed issue with pressure-assisted flush system and verified water pressure readings at approximately 160 PSI using pressure gauge. Adjusted flush valve mechanism and tested system to ensure proper operation and automatic shutoff after flush cycle completion.