HVAC & Plumbing Services in Gladstone, MO

Reworked water heater piping connections and properly mounted thermal expansion tank to ensure code-compliant installation. The existing expansion tank was repositioned and securely mounted to structural support, with copper supply lines reconfigured for proper orientation and support. All connections were tested for leaks and system operation was verified upon completion.

Removed and reset toilet to replace worn wax ring and install new stool bolts for proper sealing and stability. Installed new water supply line to ensure reliable connection between shut-off valve and toilet tank. All components tested for proper operation with no leaks detected upon completion.

Responded to clogged drain issue at lowest level of property. Upon inspection, located floor drain in utility area near water heater showing signs of corrosion and restricted flow. Previous liner installation by another company was noted in service history. Accessed drainage system behind laundry appliances where multiple PVC supply and drain lines were present. Performed diagnostic assessment of drainage infrastructure, identifying blockage in floor drain assembly. Cleared obstruction and restored proper drainage function. Verified water flow through system and confirmed resolution of reported clogging issue.

Completed plumbing estimate for replacement of water supply piping serving two residential toilets. Existing piping system is over 20 years old and requires replacement while maintaining current toilet fixtures. Assessment conducted of both bathroom locations to determine scope of work for supply line replacement and connection points.

Responded to clogged drain service call and performed toilet removal to access main drain line. Upon inspection, found deteriorated wax ring seal at toilet flange requiring replacement. Removed existing toilet, cleared obstruction from drain opening, and cleaned flange surface. Installed new wax ring seal and reinstalled toilet with proper alignment to flange. Reconnected water supply line to fill valve and tested for leaks. Verified proper flush operation and drainage flow restored to normal function.

Responded to service call for garbage disposal replacement and leaking pipe investigation in a 40-year-old residence. Upon inspection of the under-sink plumbing system, assessed the existing garbage disposal unit and connected drainage piping for signs of failure and water intrusion. Identified compromised connections and aging drain lines exhibiting corrosion and deterioration at multiple junction points. Removed the failed garbage disposal unit and disconnected associated drain fittings. Inspected the sink flange, mounting assembly, and discharge elbow for proper sealing and structural integrity. Evaluated the existing PVC drainage configuration, noting darkened areas around joints indicating previous moisture exposure and potential seal failure. Installed new garbage disposal unit with fresh mounting hardware and properly torqued all connection points to manufacturer specifications. Replaced deteriorated drain fittings and tailpiece connections to ensure watertight seals throughou

Responded to service call for sump pump making unusual noises within first year of installation. Upon arrival, inspected the sump pump system and associated electrical components in basement utility area. Evaluated pump operation, power supply connections, and backup battery system to diagnose the source of the reported sound issue. Documented existing conditions with photos showing electrical setup and equipment configuration for warranty and service records.

Completed installation of drain stopper assembly for kitchen sink. Verified proper operation of existing P-trap configuration, garbage disposal connection, and dishwasher drain line integration to ensure new stopper functions correctly with current plumbing system.

Responded to a sewer line backup in the basement. Upon arrival, found significant water damage and staining on the concrete floor radiating from the main drain cleanout pipe, with evidence of recent sewage overflow. Deployed professional drain cleaning equipment and performed mechanical augering of the main sewer line through the basement cleanout access point. Successfully cleared the blockage and restored proper drainage flow. Set up air circulation equipment to assist with drying the affected floor area following the water intrusion.

Responded to reported water heater leak at copper pipe fittings in kitchen closet location. Upon inspection, identified aging copper supply lines with significant corrosion and oxidation showing characteristic brown patina consistent with extended service life. The pressure reducing valve assembly and associated threaded connections exhibited wear and deterioration at multiple fitting points, confirming the source of reported water leakage. Documented existing plumbing configuration including corroded copper piping, pressure regulation components, and mounting hardware for service records and recommended repairs.

Completed comprehensive whole-home plumbing inspection as part of promotional campaign. Inspected A.O. Smith Energy Saver water heater installation, verified proper copper piping connections, assessed condition of supply lines and fittings, and examined HVAC system components including sensors and controls. All plumbing systems found to be in proper working order with no deficiencies or repairs required at time of inspection.

Completed a full repipe of main floor bathroom drainage system, removing deteriorated cast iron and galvanized piping. Removed toilet from flange and cut out cast iron back to the wye fitting at foundation wall. Carefully extracted cast iron from the hub while preserving the existing wye connection cast into the foundation. Installed a fernco hub adapter to transition from cast iron to PVC at the hub connection. Ran new PVC drainage piping to service the vent stack, bathtub drain, lavatory drain, and installed new toilet flange. Reinstalled the original toilet onto the new flange. Conducted comprehensive leak testing on all fixtures with water flow to verify integrity of new pipe runs. Removed all construction debris and materials from the workspace upon completion.

Completed main line horizontal drain line replacement in basement area. Removed deteriorated drainage piping and installed new PVC drainage system with proper pitch and connections to existing plumbing infrastructure. Work included securing new piping to floor joists with appropriate hangers and ensuring all joints were properly sealed for code compliance.

Responded to reported water leak in basement originating from both the main water line and water heater. Upon inspection, discovered severely corroded copper piping with significant oxidation and deterioration throughout the plumbing system. The horizontal water supply line exhibited extensive green and white corrosion buildup, indicating prolonged moisture exposure and advanced pipe degradation. Wall surfaces behind the piping showed vertical streaking patterns consistent with active water seepage. Evaluated the compromised pipe sections, isolation valves, and connection points to identify leak sources. Documented the condition of the aging copper and iron pipe assembly, including deteriorated fittings and joints. The plumbing infrastructure displayed signs of long-term water damage requiring immediate attention to prevent further structural compromise and water waste.

Accessed and serviced lower clean out cap located in yard area. Documented existing ground conditions and clean out accessibility with photographic evidence showing utility access cover embedded in exposed soil with scattered gravel and disturbed earth surrounding the work site.

Performed water leak detection service, identifying mineral buildup and corrosion at the connection point between supply line and toilet tank fitting. Inspected basement plumbing system including water heater, expansion tank, and associated copper/PVC piping to locate source of leak.

Diagnosed and repaired bathroom faucet leaking into cabinet below. Inspected the plumbing connections inside the wooden cabinet housing the PVC pipe fittings and resolved the leak. Verified proper operation of the chrome dual-handle faucet with no further leakage present.

Performed service on tanked water heater, cleaning corroded drain valve and surrounding area to restore proper drainage function. Inspected running toilet in bathroom, identifying and repairing worn internal components to eliminate continuous water flow. Documented significant corrosion around water heater drainage components with photographs for service records.

Successfully completed kitchen faucet replacement as requested by customer. Installed new customer-supplied faucet with dual control knobs and separate sprayer attachment onto double-basin stainless steel sink. Tested water flow and confirmed proper operation with no leaks.

Cleared bathroom sink clog by disassembling the PVC P-trap assembly and removing accumulated debris around the drain. After cleaning, reassembled the plumbing components including the P-trap and braided stainless steel supply lines, and verified proper drainage with no leaks.