HVAC & Plumbing Services in Kansas City, MO

Responded to service call for two malfunctioning toilets in main bathrooms. First toilet exhibited continuous running condition due to faulty fill valve assembly. Inspected tank components and identified worn flapper seal and improperly adjusted float mechanism causing constant water flow. Second toilet produced loud noise during and after flushing, traced to defective fill valve creating water hammer effect. Removed tank lids on both units for diagnostic inspection. Documented existing flush valve assemblies, float ball valve systems, and internal tank mechanisms via photographs. Addressed both issues by adjusting float heights, checking flush valve seals, and ensuring proper water pressure regulation to eliminate running water and noise concerns.

Completed preventive maintenance agreement renewal service including comprehensive tankless water heater flush procedure. Performed descaling flush on tankless unit to remove mineral buildup and maintain optimal heating efficiency, inspected all plumbing connections and water treatment system components including water softener with digital control unit, verified proper operation of all mechanical systems in utility area.

Installed two shut-off valves under lavatory sink by cutting access into cabinet wall to reach water supply lines. Building water supply was shut down to facilitate cutting into existing lines and installing isolation valves for the faucet. Following valve installation, faucet cartridges were removed and replaced with new cartridges supplied by property owner, restoring proper operation to the fixture.

Responded to clogged bathroom sink on main level. Upon inspection, identified blockage in drain line beneath vanity. Accessed plumbing from basement level and cleared obstruction from cast iron drain pipe using appropriate drain clearing equipment. Verified proper drainage flow at fixture and confirmed no leaks at connections. Sink now draining properly with full water flow restored.

Completed preventive maintenance inspection on 4-year-old heating unit located in basement. Performed comprehensive system evaluation including visual inspection of all accessible components, verified proper operation of control board and electrical connections, and documented equipment condition with photographic evidence. Unit operating within normal parameters with no immediate service needs identified.

Completed preventive plumbing maintenance on single-unit Rinnai tankless water heater system. Inspected all plumbing connections, copper piping, flexible stainless steel supply lines, and shut-off valves for proper operation and potential leaks. Verified HVAC integration components, drainage collection system, and mounting hardware integrity. All equipment found to be functioning within normal parameters.

# Plumbing Maintenance Visit Completed Performed preventive plumbing maintenance inspection on residential property. Inspected accessible plumbing infrastructure including copper supply lines, shut-off valves, and T-junction fittings in utility area. Noted advanced corrosion and oxidation on vertical copper piping and central valve assembly, with visible rust patina, mineral deposits, and scale buildup throughout system. Documented condition of plumbing components showing significant age-related deterioration. Checked under-cabinet areas and accessible pipe runs for leaks or immediate concerns. Photographed corroded valve mechanisms and copper pipe assemblies for maintenance records. System remains operational with no active leaks identified during inspection.

Installed a new 2" PVC drain line by tying into an existing 2" stack located in the cavity between the men's and women's restrooms, routing the drain line through the wall to a new washing machine location in the accessible restroom stall. Ran PEX water supply lines from the water heater room to the new laundry box location, installing shut-off valves at the water heater connections with red and blue valve handles. Removed necessary sheetrock sections to access stud cavities for pipe routing, installed the laundry box with venting extended into the attic space, and secured all piping with stud guards and mounting brackets to protect against future damage. Pressure tested all connections for leaks, verified proper drainage, and cleaned the work area of all construction debris upon completion.

Responded to main floor bathroom with shower backup and water surfacing around toilet base following recent city sidewalk construction. Upon arrival, found toilet in severely deteriorated condition with extensive mineral deposits, rust staining, and corroded mounting bolts. City water department had previously cleared main line with no issues found. Removed and replaced failing toilet fixture with new two-piece unit, installed with proper wax ring seal and new supply line. Verified proper drainage and seal integrity. Testing confirmed no further water backup issues at toilet or shower drain. New fixture installed and operational.

Performed routine maintenance flush on dual tankless gas water heater system. Isolated units using service valves, connected circulation pump and flushing equipment, and ran descaling solution through both heat exchangers to remove mineral buildup and maintain optimal efficiency. Verified proper operation of all connections, tested system pressure, and confirmed units returned to normal function upon completion.

Completed plumbing maintenance visit to address valve replacement in basement utility area. Removed deteriorated brass shutoff valve showing significant corrosion and patina buildup, as evidenced by turquoise-green copper oxidation residue on floor surface. Installed new valve assembly with proper copper pipe connections to restore water control functionality to the system.

Performed plumbing inspection and documentation of bathroom toilet system. Upon examination, identified significant rust staining and mineral deposit accumulation inside toilet tank, indicating potential internal component deterioration and water quality issues affecting fixture longevity. Assessed flush mechanism and fill valve assembly for operational integrity. Photographed existing conditions for maintenance records, including tank interior deterioration and surrounding wall discoloration near fixture installation point.

Responded to water treatment assistance request in basement utility area. Inspected residential water heater system including copper supply lines, expansion tank, gas connections, and dual ball valve assembly. Documented complete installation setup showing proper expansion tank mounting, gas line configuration with yellow supply piping, red circulation pump assembly, and water heater specifications. Verified all plumbing connections, valve operations, and system components for proper water treatment functionality and safety compliance.

Completed comprehensive plumbing inspection of water pressure monitoring system in utility area. Documented ProLine pressure gauge readings showing approximately 180 PSI on brass fittings connected to water supply line, with gauge displaying proper functionality and clear zone indicators. All connections, brass fittings, and valve assemblies were inspected and photographed for service records.

Responded to service call for garbage disposal unit emitting burning smell and failing to operate. Upon inspection, identified failed motor in existing black disposal unit mounted under kitchen sink. Disconnected electrical supply and plumbing connections including drain lines and dishwasher discharge hose. Removed defective disposal unit from sink mounting assembly. Installed new garbage disposal unit, reconnected all plumbing components including P-trap and drain lines, and restored electrical connection. Tested unit for proper operation, verified no leaks at connections, and confirmed normal function without burning odor.

Completed installation of State ProLine Commercial Grade water heater with associated piping and expansion tank in residential utility room. Installed copper supply and discharge lines with brass compression fittings and shutoff valves, connected thermal expansion tank with proper isolation valve, and installed flue vent piping per manufacturer specifications. All connections pressure tested and verified operational, with system secured to structure using appropriate mounting hardware and pipe supports.

Prepared estimate for installation of two customer-supplied stem valves on the back porch water supply system. Assessed existing plumbing configuration consisting of two copper supply lines with shut-off valves featuring green handles, flexible braided metal supply lines, and gray corrugated flexible hose secured to wall with mounting brackets. Documented current condition of washing machine hookup connections and valve assembly through photographs for accurate quote preparation.

Responded to service call for gas water heater with non-functioning pilot light in utility room off garage. Upon arrival, conducted visual inspection and confirmed no water leakage at base of unit, ruling out tank failure. Accessed burner assembly and pilot light components to diagnose ignition system failure. Cleaned pilot assembly, inspected thermocouple for proper positioning and functionality, and tested gas supply to pilot orifice. Relit pilot light following manufacturer safety procedures and verified flame stability and proper blue coloration. Tested main burner ignition cycle and confirmed water heater returned to normal operation with adequate heat production.

Replaced two customer-supplied faucets in separate bathroom locations. Addressed and repaired a leaking toilet in one of the bathrooms to restore proper function and eliminate water waste.

Responded to service call for kitchen sink not draining on main floor. Upon arrival, inspected stainless steel double-basin sink with dual garbage disposal units. Assessed drainage issue in affected basin and cleared blockage from disposal system. Tested both basins for proper water flow and verified garbage disposal units were functioning correctly. Confirmed complete drainage restoration and left work area clean and operational.