HVAC & Plumbing Services in Kansas City, MO

Responded to plumbing service call to address sinkhole remediation and clean-out pipe finishing work. Procured and transported topsoil to site, then filled and graded the developed sinkhole area to restore proper ground level. Trimmed clean-out pipe to sit flush with yard elevation and installed cap in final position at ground level, ensuring proper accessibility while maintaining a clean, level finish with surrounding landscape.

Completed preventive plumbing maintenance inspection on residential water heater and associated piping system located in basement. Unit is under 10 years old and showing normal operational condition. Inspected water heater tank, copper supply lines, brass fittings, and connection points for signs of corrosion, leaks, or mineral buildup. Observed minor mineral deposits and crystalline accumulation at pipe connections, consistent with typical water chemistry in the area. All mounting brackets and support straps verified secure. Copper piping and joints examined for integrity with no active leaks detected. System pressure and safety components functioning within normal parameters.

Responded to service call for gas water heater with pilot light that would not stay lit. Upon arrival, inspected the gas control valve, thermocouple, and pilot assembly. Cleaned the pilot orifice and thermocouple to remove debris and buildup that was preventing proper flame sensing. Successfully relit the pilot light and verified stable ignition with characteristic blue flame pattern. Tested burner operation to confirm main gas valve engagement and proper combustion. Unit restored to full operational status with pilot remaining lit and water heater functioning normally.

Responded to service call for tanked water heater with pilot light that would not remain lit. Upon inspection of the unit in the basement, diagnosed faulty thermocouple as the cause of pilot outage. Replaced thermocouple, tested pilot light operation, and verified proper flame sensor function to ensure safe and reliable water heater operation.

Completed installation of a STATE 50-gallon natural gas water heater (model BFG2H5040T3NOV) with 40,000 BTU input rating. Removed and properly disposed of existing water heater equipment. Installed new thermal expansion tank mounted on wall bracket to protect system from excessive pressure buildup. Installed ball valve shut-off on cold water supply line and gas shut-off valve on gas supply line per code requirements. Connected all gas piping with proper fittings and verified leak-free connections. Installed temperature and pressure relief valve with discharge pipe terminating safely per plumbing code. Verified proper venting configuration with existing flue system and confirmed adequate combustion air supply. Tested all connections for leaks, filled tank, purged air from system, and verified proper ignition and burner operation. Unit is operating within manufacturer specifications with proper temperature settings. Installation includes one-year labor warranty and six-year manufacturer'

Completed plumbing maintenance inspection at residential property, examining toilet supply line connections and main water distribution system in basement utility area. Inspected copper supply lines, shut-off valves, and control devices to ensure proper operation and verify system integrity with no leaks detected.

Conducted comprehensive assessment of existing sump pump system in basement utility area to provide replacement estimate. Current sump pump unit operational at time of inspection, housed within enclosed chase space with electrical service and discharge piping in place. Documented existing installation configuration including pump location, electrical connections via wall-mounted outlet box, and drainage routing through corrugated flexible discharge line. Evaluated mechanical chase accessibility, structural framing, and equipment clearances to determine optimal replacement specifications and installation requirements for new sump pump system.

Completed comprehensive cooling season tune-up on single AC unit less than ten years old. Performed standard maintenance protocol including system inspection, temperature differential measurements across evaporator coil (recorded 94.1°F), verified proper airflow through condenser fins, and confirmed optimal operating parameters. All components found in good working condition with no deficiencies noted.

Performed maintenance inspection on tankless water heater unit. Removed front access panel to examine internal components including heat exchanger, burner assembly, control boards, and electrical connections. Verified proper operation of all mechanical systems, checked gas line connections and water line fittings for secure installation, and inspected PVC intake and exhaust venting. Documented equipment condition with photos showing clear liquid sample and internal component configuration. All systems found operational with components properly installed and connected.

Completed six-month follow-up visit to finish grading work around previously installed sewer top hat assembly. Trimmed pipe to proper height and regraded surrounding soil to ensure proper drainage and ground stability. All work performed on exterior property with area left clean and ready for final landscaping restoration.

Removed and disposed of six-year-old 50-gallon gas water heater exhibiting defective temperature and pressure relief valve and failed thermal expansion tank, both components no longer covered under warranty. Installed new 50-gallon gas State brand water heater with copper piping connections, brass fittings, and valves. Additionally installed new thermal expansion tank and pressure reducing valve to protect the system and ensure proper water pressure regulation. All connections tested and verified for proper operation with one-year labor warranty and six-year manufacturer's warranty provided.

Completed preventative plumbing maintenance inspection on residential property. Verified proper operation of bathroom shower fixture with handheld showerhead, confirmed adequate water flow and spray pattern, and inspected plumbing connections behind access panel. Examined mechanical system components including filter assembly, refrigerant lines with brass fittings, and associated ductwork insulation for signs of leaks or deterioration. All fixtures and connections found to be functioning within normal parameters with no immediate repairs required.

Responded to a main line repair for a failed hose bib supply line. Upon inspection, discovered the copper pipe connection to the exterior hose bib had separated, causing a complete line failure. Removed the damaged section of copper piping, fabricated new connections with proper fittings and soldered joints, and restored water supply to the hose bib. System tested and verified leak-free operation upon completion.

Completed replacement of two outdoor hose bibs and one shower control valve assembly. Installed new frost-free sillcocks with proper mounting hardware on exterior wood siding, including connection points compatible with existing hose attachments. Replaced shower mixing valve and trim kit with chrome finish single-handle unit, ensuring proper water temperature control and flow regulation. All fixtures tested for leaks, proper operation verified, and connections secured to manufacturer specifications.

Completed preventive plumbing maintenance inspection of residential water heater and sump pump system. Inspected water heater tank, copper supply lines, pressure relief valve, and associated plumbing connections for proper operation and signs of wear. Examined sump pump assembly including motor, float switch mechanism, and discharge system; noted existing mineral buildup and staining consistent with normal operation but requiring future monitoring.

Responded to multiple water leak issues including an exterior hose bib with valve leakage, a garage shut-off valve experiencing dripping when activated, and a deteriorated three-inch black drain pipe beneath a sink that had been leaking for an extended period. Inspected and documented the outdoor spigot assembly showing weathered valve components and the basement drainage system exhibiting significant mineral buildup and corrosion around the pipe opening. Assessed all affected areas and provided repair recommendations to address the active leaks and prevent further water damage.

Conducted estimate for servicing Puronics water softener system located in basement utility area. Inspected water treatment equipment including stainless steel brine tank, softener resin tank, and associated plumbing connections with copper supply lines and PVC drainage piping. Assessed system condition, documented current installation configuration, and identified service requirements for proper water softening operation.

Performed comprehensive sump pump inspection and customer education for homeowner new to property with two existing basement sump pump systems. Evaluated both pump installations, discharge line routing, and exterior drainage termination points. Identified discharge line in yard with visible PVC piping and brick-lined trench area requiring attention. Explained operational functionality of both sump pump units, automatic float switch mechanisms, and proper maintenance procedures to homeowner. Provided recommendations for system improvements and ongoing maintenance requirements to ensure reliable basement water protection.

Installed a 50-gallon gas water heater in the basement utility area, complete with all necessary plumbing connections including copper supply lines, gas line hookup, and proper venting through metallic ductwork. A thermal expansion tank was mounted to the cold water supply line to protect against pressure fluctuations in the system. All connections were tested and verified operational, with appropriate safety valves and shutoff mechanisms installed per code requirements.

Completed plumbing maintenance visit to inspect and verify proper operation of bathroom sink faucet and associated supply and drainage systems. Tested water flow and pressure at chrome single-handle faucet, confirmed proper drainage through P-trap assembly, and inspected under-sink plumbing connections including flexible braided supply lines, shut-off valves, and PVC drain components to ensure all fixtures were functioning correctly without leaks.