HVAC & Plumbing Services in Kansas City, MO

Replaced the temperature and pressure relief valve on the residential water heater to ensure proper safety operation. Installed a new expansion tank to the plumbing system to accommodate thermal expansion and protect against excessive pressure buildup in the closed water heating system. All connections were properly secured with appropriate fittings, and the system was tested for leaks and proper functionality upon completion.

Responded to service call for Rinnai tankless water heater displaying error code 55 in basement. Diagnosed and resolved the issue, verified unit returned to proper operation with temperature control showing 120°F on digital display. Documented installation with photos showing copper piping connections, isolation valves, and proper mounting configuration.

Conducted comprehensive sewer line estimate for secondary line replacement due to root infiltration. Reviewed existing camera footage showing root penetration in exterior line section. Assessed basement plumbing configuration including connection points where exterior secondary line joins main interior sewer system. Evaluated structural access points, existing copper supply lines, and utility space constraints to determine optimal routing for replacement line. Documented current plumbing infrastructure and provided detailed replacement estimate for secondary sewer line installation.

Responded to reported kitchen sink clog and performed diagnostic assessment of drainage system. Upon inspection, accessed plumbing infrastructure in basement utility area beneath kitchen to evaluate drainage lines and identify blockage source. Documented existing plumbing configuration including PVC drainage piping, copper supply lines, and mechanical connections. Prepared work area with catch basin positioned under drainage system to contain water during diagnostic procedures and potential repair work.

Installed a new 1" gas line from existing basement supply to exterior generator location. Tied into accessible 1" gas line in basement with drop ceiling using a 1" tee fitting and shut-off valve, transitioned to flexible gas line for routing to back wall, then switched back to rigid pipe before penetrating exterior wall. Ran hard pipe along exterior deck perimeter to generator location, installed 90-degree fitting and reduced to 1/2" gas line with shut-off valve and drip leg at generator connection point. Performed pressure testing to verify system integrity and confirm no leaks present. Left gas supply valve in closed position pending generator commissioning.

Replaced a failed 0.5 horsepower grinder pump with new unit, including proper electrical connections and discharge piping. Repaired exterior hose bib, installing a Prier or Woodford-style frost-free sillcock to prevent future freeze damage. Verified all connections for proper operation and tested system functionality upon completion.

Performed routine plumbing maintenance inspection of water heating system and under-sink plumbing. Inspected Performax Gel water heater installation in utility closet, verifying proper copper piping connections, expansion tank mounting, and safety label compliance. Examined under-sink cabinet plumbing, confirming PVC trap assembly and drain connections were functioning properly with no visible leaks or drainage issues.

Performed hydro jetting service to clear main sewer line blockage at residential property. Utilized high-pressure water jetting equipment to remove accumulated debris, grease buildup, and root intrusion from drainage system, restoring proper flow and functionality to the plumbing system.

Completed on-site assessment for kitchen faucet replacement estimate. Evaluated existing single-handle pull-down faucet with chrome finish installed on stainless steel double-basin sink with decorative tile backsplash. Documented current plumbing configuration including supply line connections, shut-off valves, and mounting hardware to provide accurate replacement pricing and scope of work.

Responded to service call for 30-year-old water heater that leaked onto floor and extinguished pilot light, rendering unit inoperable. Assessed existing Rheem tank-style water heater located in basement and documented current installation configuration including supply lines, venting, and electrical connections. Provided estimate options for replacement including tankless water heater systems and traditional tank-style units to meet customer's needs.

Completed installation of a 40-gallon gas-fired water heater in the basement utility area with all required connections to existing copper supply lines and gas piping. Installed and secured a thermal expansion tank with proper mounting hardware and connected it to the cold water supply line to protect the system from excessive pressure buildup. All connections were tested for proper operation and leak-free performance prior to completion.

Installed new Toto Drake toilet in bathroom, including new wax ring seal and supply stop valve. Completed all necessary plumbing connections with braided stainless steel supply line, ensuring proper water flow and leak-free operation.

Responded to a clogged toilet in the hallway bathroom. Upon inspection, accessed the plumbing beneath the fixture and inspected the P-trap and drain assembly for blockages. Cleared the obstruction and verified proper drainage and flush operation before completing the service.

Responded to a floor drain blockage in the basement utility area. Upon arrival, observed evidence of recent water backup and cleaning attempts on the concrete floor surrounding the drain. Successfully cleared the obstruction using appropriate drain cleaning equipment, restoring proper drainage function and preventing further water accumulation in the work area.

Responded to service call for non-operational sump pump caused by tripped breaker, resulting in 4 inches of standing water in basement area. Reset breaker and restored power to sump pump system, verified proper operation and water discharge. Inspected and assessed exterior water spigot that sustained freeze damage during recent cold weather event, confirmed burst fitting requiring replacement. Documented mechanical room conditions including water heaters, HVAC equipment, and plumbing infrastructure for service records.

Responded to service call for collapsed PVC piping near street on vacant property. Upon arrival, located previously marked collapse area in street using utility locating equipment to verify underground pipe position and assess extent of damage. Documented site conditions including driveway access, street surface markings, and proximity to property structures for estimate preparation.

Installed 3/4" tech line with two SharkBite fittings on A.O. Smith water heater, creating a recirculation loop configuration. Drained and flushed sediment from the existing water heater tank to maintain efficiency and longevity. All copper piping connections with brass fittings and black foam insulation were properly secured, and the system was tested for proper operation with no leaks detected.

Completed annual plumbing maintenance inspection covering residential bathroom fixtures and basement mechanical systems. Inspected bathroom vanity faucet, drain assembly, and supply lines for proper operation and leaks; verified basement drainage piping, PVC connections, and utility room plumbing infrastructure for structural integrity and code compliance.

Conducted plumbing estimate for underground piping system replacement due to collapsed pipe. Inspection revealed extensive rust and corrosion on existing metal piping infrastructure located in crawl space, with significant oxidation present on horizontal pipe sections and connection fittings. Documented conditions of deteriorated piping system, including corroded metal flanges and couplings, to provide accurate assessment for complete pipe replacement and system restoration.

Responded to service call for leaking Rinnai tankless water heater. Upon inspection, identified active leak at brass valve assembly and pipe connections. Photographed affected components including blue-handled ball valves, brass fittings showing corrosion and mineral buildup, and associated piping. Documented condition of valve internals, threading, and mounting hardware. Provided estimate for necessary repairs to address leak source and restore system integrity.