HVAC & Plumbing Services in Kansas City, MO

Responded to service call for failed garbage disposal unit in kitchen. Removed existing inoperative disposal and installed new replacement unit. Connected disposal to existing sink drain assembly and verified proper alignment with P-trap configuration. Tested unit operation and confirmed proper drainage with no leaks at connection points.

Responded to report of slow leak at master bathroom shower drain. Accessed plumbing system from basement below to inspect drain lines and connections. Upon investigation, discovered significant water staining and corrosion around shower drain assembly, indicating prolonged moisture exposure. Inspected PVC drain piping running through floor joists and confirmed leak origin at drain flange connection. Documented existing conditions showing deteriorated drain seal and mineral buildup on drain components. Provided assessment of leak source and recommended repair options to address compromised drain assembly and prevent further water damage to structure.

Replaced existing three-handle shower valve with new Moen Posi-Temp single-handle pressure-balancing valve. Created access point through adjacent side wall to facilitate installation, then installed oversized three-handle escutcheon trim plate to conceal previous valve mounting holes in tiled shower wall.

Responded to service call for low water pressure throughout residence. Upon inspection, identified clogged faucet aerators as primary cause of reduced water flow. Removed and cleaned aerator screens from affected fixtures, removing mineral deposits and sediment buildup. Inspected internal components including washers and flow restrictors for wear and damage. Reinstalled aerators and tested water pressure at multiple fixtures to confirm restoration of normal flow rates throughout the home.

Conducted comprehensive assessment of 16-year-old sump pump system in residential basement to provide estimate for replacement unit. Evaluated existing operational pump, basin installation, discharge piping, and electrical connections. Documented significant moisture damage, water staining on surrounding floor joists and framing, and evidence of mold growth around basin perimeter, indicating historical water intrusion issues that will require remediation during pump replacement.

Completed installation of a 50-gallon gas-fired water heater in basement utility space. Installed thermal expansion tank to protect against excessive pressure buildup in the closed plumbing system. Connected all necessary copper supply lines with proper shut-off valves and installed pressure relief valve with discharge piping. Configured gas supply connection and venting system using code-compliant black pipe and galvanized vent piping with appropriate elbow fittings to ensure safe exhaust of combustion gases. All plumbing connections were pressure-tested and verified for proper operation. Unit was commissioned and confirmed to be heating water efficiently with no leaks detected at any connection points.

Responded to emergency plumbing call for severe leak from three-handle shower valve assembly in upstairs bathroom that required shutting off water supply to entire house. Removed existing three-handle shower trim and valve stems, assessed wall cavity for water damage, and converted system to modern single-handle pressure-balancing valve. Installed new single-handle trim kit with chrome finish, tested for proper operation and leak-free connections, and restored water service to residence.

Successfully installed a 50-gallon gas water heater with thermal expansion tank in the utility area. Completed single wall flue rework up to 4 feet to ensure proper venting. All copper supply lines were connected with shutoff valves, gas line was properly fitted with shutoff valve, and the system was tested for proper operation and safety compliance.

Installed new gas line to supply standby generator. Ran black iron pipe from existing gas meter through exterior wall penetration and terminated at generator connection point. Routed piping along building exterior with proper support brackets and performed pressure test to verify system integrity and code compliance.

Performed hydro-jetting service on exterior drainage system located in outdoor paved courtyard area. Removed metal drain grate to access main drain line opening. Deployed high-pressure water jetting equipment to clear blockages and buildup from the drain line. The drain showed signs of accumulated debris, sediment, and organic matter from prolonged exposure to outdoor elements. Successfully cleared the line to restore proper drainage flow. Reinstalled drain cover upon completion. Documented pre-service and post-access conditions with photographs showing drain location and surrounding paved surface area.

Responded to service call for no hot water and malfunctioning toilet flush valve in main bathroom. Inspected gas-fired A.O. Smith water heater in basement utility area and verified lack of hot water production throughout home. Examined toilet tank components and identified failed flush valve requiring replacement due to mineral buildup and component wear. Replaced defective flush valve assembly with new unit, tested flushing mechanism for proper operation, and verified tank refill cycle functioning correctly.

Removed existing drinking fountain and installed new Elkay wall-mounted combination unit featuring both bottle filler station and traditional drinking fountain in guest laundry area. Connected water supply lines, drainage piping including white PVC with appropriate fittings, and installed shutoff valve assembly to mechanical system. Tested all connections for leaks and verified proper operation of both bottle filling sensor and drinking fountain basin.

Responded to emergency service call for water heater with blown gasket. Upon arrival, water supply had already been shut off by customer to prevent further flooding. Inspection revealed significant internal corrosion and rust accumulation around the tank base and drain assembly, indicating advanced deterioration of the unit. The pressure tank system showed external condensation and corroded copper piping connections, suggesting ongoing moisture issues within the plumbing system. Assessed the extent of damage to determine whether gasket replacement was viable or if full unit replacement would be required due to the severity of internal corrosion observed at the tank bottom and drainage components.

Responded to service call addressing three plumbing issues in residential bathrooms. Replaced faulty toilet flapper valve that was causing tank leakage, removing the stuck original flapper and installing new red rubber replacement component to restore proper seal and eliminate water waste. Installed customer-provided bathtub spout diverter assembly on Moen tub fixture after original water redirection mechanism failed, securing new brushed metal spout with proper mounting hardware. Reinstalled bathroom sink pop-up drain stopper assembly, reconnecting pivot rod and linkage to restore proper drain operation.

Responded to service call for tankless water heater not producing hot water through two shower heads in bathrooms. Upon arrival, diagnosed and repaired the tankless water heater system to restore proper hot water delivery to the affected fixtures. System tested and confirmed operational with adequate hot water temperature output at all points of use.

# Patio Drain Cleaning - Slow Drainage Issue Resolved Responded to service call for patio drain experiencing significantly reduced flow rate. Upon arrival, inspected square drain basin installed in concrete patio floor showing visible signs of debris accumulation and standing water around drain fixture. Performed thorough assessment of drainage system and identified blockage causing slow water evacuation. Cleared obstruction from drain line using appropriate drain cleaning equipment and techniques. Removed accumulated organic debris, sediment, and buildup from drain basin and surrounding area that was contributing to poor drainage performance. Tested drain flow after clearing blockage to verify proper water evacuation and confirm restoration of normal drainage function. Patio drain now operating at full capacity with no standing water remaining in basin area.

Responded to guest bathroom for customer-provided toilet installation. Removed existing toilet fixture, including disconnection of water supply line and wax ring removal. Prepared flange and floor surface for new installation. Set new toilet unit with fresh wax ring seal, ensuring proper alignment with floor flange and decorative tile pattern. Connected braided stainless steel supply line to fill valve and shut-off valve. Secured toilet to floor with closet bolts and tested for proper seating. Turned on water supply, filled tank, and performed multiple flush cycles to verify proper operation and check for leaks at supply connection, tank-to-bowl seal, and base. Confirmed stable installation and no water seepage. Installation completed successfully with all connections secure and fixture functioning properly.

# Plumbing Maintenance Inspection Completed comprehensive plumbing maintenance inspection per scheduled service request. Inspected water heater installation in basement mechanical room, including expansion tank, supply and discharge piping, pressure relief valve, and all associated connections. Verified proper clearances, examined pipe insulation integrity, and assessed overall system condition. Customer inquired about water heater flushing capability during inspection visit; confirmed unit can be flushed and provided guidance on maintenance procedures. Inspected kitchen plumbing fixtures including Kohler undermount sink, hot and cold water supply lines, drain assembly, and brass faucet installation. Tested faucet operation and water flow, verified proper drainage, and checked for visible leaks at all connections. All plumbing systems inspected were found to be in proper working condition with no immediate repairs required.

Responded to service call for non-functioning water softener installed in basement several months prior. Upon arrival, confirmed unit was not consuming salt and water exhibited no softening characteristics. Performed diagnostic inspection of water softener system, checking bypass valve position, control valve settings, and regeneration cycle programming. Examined inlet and outlet plumbing connections, verified proper water flow direction through the system, and inspected brine tank assembly for proper salt bridge or mushing conditions. Tested system controls and verified electrical connections to ensure proper power supply to control head. Identified installation or configuration issue preventing regeneration cycles from initiating. Made necessary adjustments to restore proper system operation and verified water softening function was restored.

# Plumbing Maintenance Visit Conducted comprehensive plumbing inspection in basement utility area, documenting extensive mineral buildup and corrosion on vertical copper piping system. Photographed deteriorated copper pipes showing significant white crusty deposits and oxidation, along with existing PVC, brass fittings, and flexible connector installations mounted to structural framing. Assessment revealed advanced pipe corrosion requiring monitoring or potential replacement to prevent future leaks or system failure.