HVAC & Plumbing Services in Kansas City, MO

Excavated and removed existing broken and sunken pit from service location. Installed new pit with proper backfill compaction around exterior perimeter to ensure structural stability. Completed installation with new lid and cap assembly, then restored work area to clean condition upon project completion.

Responded to service call for gas line extension and shower valve repair. Extended natural gas line from main supply along exterior of house to accommodate installation of natural gas generator. Replaced Moen shower cartridge due to lack of cold water delivery; addressed pressure balancing spool issue to restore proper temperature control and water flow to shower fixture.

Completed comprehensive whole-home plumbing inspection at customer's request with no reported issues or concerns. Thoroughly examined all accessible plumbing systems, fixtures, and components throughout the property. Inspected water heater installation, including proper venting, temperature and pressure relief valve, supply and discharge piping connections, and overall unit condition. Verified all visible plumbing connections, supply lines, and drainage systems for proper operation and potential concerns. Documented findings with photographic evidence for customer records.

Responded to service call for low water pressure issues affecting multiple fixtures in Jack and Jill bathroom. Investigated bedroom sink with adequate cold water pressure but restricted hot water flow, as well as bathtub with insufficient water pressure on both hot and cold supply lines. Inspected shower fixture and tub assembly, examining for potential aerator blockages, valve restrictions, or sediment buildup in supply lines. Documented existing conditions including mineral deposits and fixture wear that may be contributing to inconsistent water flow and temperature control issues.

Technician responded to a follow-up service call to perform mainline sewer inspection. Upon arrival, augered the main sewer line to a depth of 40-60 feet and successfully extracted an extensive root mass measuring over 6 feet in length. Following removal of the root obstruction, performed a comprehensive camera inspection of the mainline sewer system as requested. Accessed the sewer system through the exterior cleanout located in the lawn area adjacent to the street. Documentation photos captured the sewer access point and property identification for service records.

Responded to main bathroom shower handle that would not shut off completely, causing continuous water leakage in tub that was progressing from dripping to potential stream flow. Upon inspection, diagnosed faulty valve cartridge preventing proper water shutoff. Removed shower trim and handle assembly, extracted worn cartridge, and installed replacement cartridge to restore full shutoff function. Tested hot and cold water operation to verify complete seal and proper handle operation. Leak eliminated and shower valve now functioning to manufacturer specifications.

Responded to emergency sewer backup in basement. Located main sewer cleanout and performed mechanical cable augering to clear blockage in main drain line. Extracted debris and restored proper drainage flow. Deployed extraction equipment and flexible ducting to remove remaining standing water and moisture from affected basement area. Sanitized and deodorized floor surfaces to eliminate sewage odor. Verified system functionality with water flow test and advised property owner on preventative maintenance recommendations.

Responded to callback for persistent leak at bathroom sink originally addressed on previous visit. Upon inspection, accessed plumbing behind wall cavity and identified leak source at vertical drain assembly. Leak was caused by compromised connection points on black PVC drain pipe secured with metal hose clamps. Tightened all clamp connections on the vertical waste assembly and horizontal branch lines, inspected flexible supply line connections at wall-mounted fixture, and verified proper seal at all joints. Tested system under full water pressure to confirm leak resolution. Wall access opening left available for final verification before closure.

Completed comprehensive plumbing maintenance inspection of residential property. Evaluated interior hot water circulation system including copper piping, brass fittings, control valves, and circulation pump in basement utility area, confirming proper operation and connections. Inspected exterior plumbing connections at building perimeter, including hose bibs and irrigation valve assembly, verifying functionality and seasonal readiness of outdoor water supply system.

Completed installation of a 50-gallon gas water heater in residential utility closet. Positioned unit on plywood platform alongside existing Lennox HVAC system, connected yellow gas supply line to base of heater, and ran copper piping from top of unit. Installed blue thermal expansion tank above water heater with proper copper pipe connections to manage thermal expansion and protect plumbing system from excessive pressure. All safety labels, pressure relief mechanisms, and shut-off valves installed per manufacturer specifications and local code requirements.

Conducted commercial plumbing estimate for 19-gallon electric water heater replacement at warehouse facility. Accessed elevated unit above back office door using ladder provided by customer, inspected existing 3-year-old electric water heater with copper supply lines, expansion tank, and electrical disconnect box. Unit currently operational; documented installation configuration including piping connections, mounting hardware, and mechanical room layout to provide replacement specifications.

Responded to reported toilet leak in hall bathroom. Upon inspection, identified water leaking from beneath the toilet base and migrating toward the sink area. Documented water damage to flooring surface with visible moisture present. Inspected toilet mounting, wax ring seal, and supply line connections in confined space beneath fixture. Additional repairs required to properly address leak source and restore proper function.

Responded to service call for tankless water heater with no hot water and GFCI tripping issues. Performed diagnostic inspection of unit interior, identifying potential electrical fault causing ground fault condition. Completed preventative maintenance flush of tankless system to remove mineral buildup and scale accumulation from heat exchanger. Inspected internal components including condensate collection system, electrical connections, and wiring integrity. Cleaned debris from condensate pump assembly and verified proper drainage function. Evaluated all wire connections and terminations for signs of moisture intrusion or corrosion that could contribute to GFCI tripping. Performed plumbing preventative maintenance inspection of associated water supply lines and connections. Unit operational status assessed and recommendations provided for any necessary repairs to resolve recurring GFCI fault condition.

Responded to complaint of sewer odor in upper bedroom. Conducted thorough inspection of plumbing system including water heater, supply lines, and accessible plumbing connections. Inspected wall-mounted plumbing access panel containing hot and cold water shut-off valves with braided supply lines. Examined basement mechanical room plumbing infrastructure including water heater connections, copper piping, expansion tank, and associated shut-off valves. Documented existing plumbing configuration with photos for reference. Unable to identify definitive source of sewer gas odor during this visit; recommend further investigation of drain traps, vent stack system, and wax ring seals at toilet fixtures in upper level to isolate odor source.

Responded to service call for corroded bathroom sink pipework replacement. Upon inspection, found existing chrome P-trap and drain assembly had significant corrosion preventing proper disassembly and repair. Successfully removed deteriorated plumbing components and installed new P-trap assembly beneath pedestal sink. Verified all connections for proper seal and tested drainage system to ensure full functionality. All new fixtures installed and system operational.

Responded to urgent call for water leak near furnace and hot water heater in utility closet. Upon inspection, examined all copper piping, connections, and fittings throughout the mechanical space, including water heater supply lines with yellow insulation sleeves and pressure relief valve assembly. Thoroughly inspected flexible ductwork connections, PVC drainage and venting systems, and all visible plumbing joints for signs of active leakage or moisture. Checked water heater tank exterior, control panel area, and base connections where copper pipes with brass fittings connect to unit. No active leak was identified during the inspection period; all connections, joints, and fixtures appeared dry with no visible water damage, staining, or moisture accumulation on flooring or surrounding surfaces. Documented existing plumbing configuration with photographs for reference. Advised that intermittent leaks can be difficult to diagnose without active water flow and recommended monitoring the ar

Responded to service call for broken pipe under kitchen sink. Upon arrival, inspected the cabinet area and identified damaged drain assembly requiring replacement. Removed existing P-trap configuration and drain tailpiece. Installed new brass drain tailpiece and white PVC P-trap assembly with proper threaded connections. Verified all slip-joint connections were properly sealed and tightened to manufacturer specifications. Tested drainage system for leaks and confirmed proper water flow. Cleaned work area and removed debris from cabinet space.

Responded to service call for tankless water heater with no hot water and ignition failure. Upon inspection, identified faulty flame rod connector causing intermittent electrical connection and preventing proper ignition sequence. Removed and replaced defective connector with new unit, ensuring proper pin alignment and secure locking mechanism. Tested system operation through multiple heating cycles, confirmed successful ignition, and verified consistent hot water delivery. Unit restored to full operational status.

Completed comprehensive plumbing inspection of residential property, documenting condition of water supply system components including pressure tank, brass fittings, and valves in utility space. Identified and photographed significant damage to bathroom sink basin, including large crack with missing ceramic material requiring replacement, and documented all findings for customer review.

Installed a new 40-gallon power vent water heater with thermal expansion tank in the basement utility area. The unit was properly positioned on the concrete floor with all required safety labels and specifications clearly visible. Connected the gas supply line using yellow corrugated flexible tubing to the white control valve assembly at the base of the heater. Completed all necessary plumbing connections and installed the thermal expansion tank to protect against pressure buildup in the closed water system. Verified proper venting configuration for the power vent system through the attic space, with flexible ductwork routed appropriately through structural supports and insulation. All connections were tested and confirmed operational per manufacturer specifications and local code requirements.