HVAC & Plumbing Services in Kansas City, MO

Completed comprehensive whole-home plumbing inspection as part of preventative maintenance campaign. Thoroughly examined all accessible plumbing systems including water heater, filtration equipment, supply lines, and drainage components. Inspected wall-mounted water heating system with dual blue filter cartridges, copper supply piping with brass fittings, and associated PVC drainage lines in utility area. Evaluated condition of insulated cylindrical storage tank, copper distribution lines, and flexible connector hoses in confined crawl space. Documented current system conditions with photographic evidence showing older installations with signs of age-related deterioration on surrounding surfaces. All major plumbing components found operational at time of inspection, though environment shows moisture exposure and aging infrastructure typical of older mechanical spaces.

Responded to callback for heating unit displaying error code 11 related to ignition failure, following previous repair completed on 4/29. Upon arrival, accessed the second-floor unit and removed cover panel to inspect internal components and electrical connections. Examined ignition system, control board, wiring harnesses, and gas valve assembly. Verified proper electrical connections at terminal blocks, checked wire integrity including pink and yellow leads at bus bars, and inspected control module functionality. Documented internal condition of heat exchanger, burner assembly, and all safety controls with photographs. Tested system operation and confirmed unit firing properly with no error codes present.

Installed customer-supplied Kraus KHS230-32 utility sink in garage with pump-assisted drainage system due to elevation constraints preventing gravity drain installation. Connected discharge piping to laundry stack above washing machine tie-in to maintain proper venting and code compliance, installed new supply stops and supply lines with all necessary fittings, and tested system for leaks and proper operation upon completion.

Completed scheduled plumbing maintenance visit including tankless water heater system flush and inspection. Serviced gas water heater installation with multiple shut-off valves, verified proper operation of pressure relief valve assembly, and inspected copper piping, PEX tubing, and gas line connections throughout the system. Performed maintenance on ceiling-mounted plumbing fixtures and verified all connections and mounting hardware were secure.

Responded to a water leak originating from the upper unit (Apt 8) affecting the lower unit (Apt 4). Conducted visual inspection and documentation of affected plumbing areas, revealing deteriorated pipe insulation and exposed piping components at wall and floor junctions. Observed compromised foam pipe insulation that has cracked, separated, and lost structural integrity, along with exposed metal pipes, fittings, and mounting hardware in corner cavity areas where wooden flooring meets wall paneling. Documented conditions showing evidence of moisture intrusion and age-related degradation to insulation materials surrounding plumbing infrastructure. Prepared photographic documentation and estimate for necessary repairs to address leak source and restore proper pipe insulation and protection.

Successfully installed customer-supplied kitchen faucet, including removal of existing fixture and connection of new unit to existing water supply lines. Verified proper hot and cold water supply connections using flexible braided supply lines, tested shutoff valves for proper operation, and confirmed leak-free installation with full water pressure testing.

Responded to service call for gas line removal and capping running from basement to garage. Upon inspection, found severely corroded gas piping with extensive rust deterioration throughout the line, indicating prolonged exposure to moisture and age-related degradation. The existing pipe exhibited compromised structural integrity with heavy oxidation layers covering the metal surfaces. Successfully capped the gas line at the point of origin to ensure safe termination of gas supply. Removed the deteriorated gas piping section that ran through the crawl space and into the garage area near the overhead door mechanism. Verified proper cap installation and conducted pressure testing to confirm complete gas line isolation and system safety. Documented existing conditions showing water damage to surrounding building materials and insulation in the affected area.

Completed installation of customer-supplied one-piece toilet in residential bathroom. Removed existing toilet fixture, installed new wax ring seal, and properly set and secured the new toilet to the floor flange. Connected water supply line, tested for proper operation and verified no leaks at base or supply connection.

Completed installation of new Toto Drake toilet with fresh wax ring seal. Connected water supply line with braided stainless steel flex connector to ensure reliable water delivery. Verified proper bowl water level, confirmed secure mounting to floor flange, and tested flush operation for optimal performance.

Installed two customer-supplied faucets in collaboration with related job activities. Completed under-sink plumbing connections including drain assemblies, tailpieces, and flexible braided supply lines for both hot and cold water. All components were properly secured with slip nuts and fittings, ensuring leak-free operation and code-compliant installation.

Completed installation of a 50-gallon gas water heater in mechanical room, which required relocating washer and dryer to access the work area. Removed existing unstable water heater that had been improperly supported with bricks underneath. Installed new unit with proper connections including PEX supply lines, 3/4" pressure relief valve (PRV), and 1/4 turn valve for humidifier connection. All plumbing connections were secured with brass fittings, temperature and pressure relief valve assembly was properly installed and tested, and unit was commissioned to verify proper operation and safety compliance.

Technician responded to master bathroom to provide estimate for replacing existing toilet with Toto Drake model. Performed site assessment including measurements of current toilet dimensions and rough-in spacing to verify compatibility with requested fixture. Documented existing bathroom configuration, tile work, and plumbing connections to ensure proper installation specifications for estimate preparation.

Responded to a clogged bathtub drain on the second floor hallway. Upon arrival, found the tub basin with significant standing water and visible debris accumulation in the drain opening. Utilized a mechanical drain auger to clear the obstruction, successfully removing a substantial amount of organic matter, hair, and fibrous buildup from the drain line. The blockage was completely cleared, restoring proper drainage function to the fixture.

Responded to service call for kitchen sink with no water pressure. Upon inspection, diagnosed low water pressure issue at kitchen faucet. Examined under-sink plumbing configuration including garbage disposal unit, P-trap assembly, and supply line connections. Assessed existing faucet condition and water flow restrictions. Inspected all visible plumbing components beneath sink, including white PVC drainage system and connections to disposal unit. Verified proper operation of shut-off valves and checked for potential blockages or restrictions in supply lines. Documented existing plumbing configuration with cabinet-mounted components and mechanical systems for service records.

Installed a 40-gallon State brand gas water heater in commercial utility space, replacing existing unit. Connected incoming cold water supply and outgoing hot water distribution lines using copper piping with brass fittings and shutoff valves. Installed blue thermal expansion tank to protect system from pressure buildup due to thermal expansion. Secured all gas connections, verified proper venting through existing ductwork, and ensured compliance with commercial plumbing codes. Tested system operation, confirmed proper ignition, and verified no leaks at all connection points.

Completed comprehensive whole-home plumbing inspection at customer's request. Thoroughly examined all accessible plumbing systems including water supply lines, drainage systems, and mechanical room components. Inspected copper piping, PEX tubing connections with ball valve shut-offs, brass fittings, and Bradford White water heater installation. Verified proper operation of all visible plumbing fixtures, connections, and valves throughout the property. Documented current system conditions with photographic evidence showing utility room plumbing infrastructure, supply line configurations, and appliance connections. No deficiencies or immediate concerns identified during inspection; all systems functioning as designed.

Conducted site assessment of commercial men's bathroom experiencing recurring flooding issues affecting adjacent office space. Inspected existing floor drain system and documented current drain elevation relative to bathroom fixtures and floor level. Provided estimate for drain relocation and lowering to prevent water overflow and protect office areas from future flooding events.

Completed replacement of toilet fill valve and shower cartridge to restore proper fixture operation. Installed new fill valve assembly in toilet tank to address water flow issues, and replaced worn shower cartridge to eliminate temperature control problems and leaking. All connections tested and verified for proper function with no leaks detected upon completion.

Completed installation of a 50-gallon gas-fired water heater with thermal expansion tank in residential utility space. All copper supply and discharge piping was configured to manufacturer specifications with proper shutoff valves and compression fittings. The thermal expansion tank was installed on the cold water supply line to protect against thermal expansion in the closed plumbing system. All connections were pressure-tested and verified for proper operation before completing the installation.

Performed plumbing maintenance inspection on residential water heater system. Conducted internal camera inspection of water heater tank to assess sediment buildup and interior condition, and documented copper supply line connections and plumbing configuration for maintenance records.