HVAC & Plumbing Services in Kansas City, MO

Responded to service call for gas line removal and capping running from basement to garage. Upon inspection, found severely corroded gas piping with extensive rust deterioration throughout the line, indicating prolonged exposure to moisture and age-related degradation. The existing pipe exhibited compromised structural integrity with heavy oxidation layers covering the metal surfaces. Successfully capped the gas line at the point of origin to ensure safe termination of gas supply. Removed the deteriorated gas piping section that ran through the crawl space and into the garage area near the overhead door mechanism. Verified proper cap installation and conducted pressure testing to confirm complete gas line isolation and system safety. Documented existing conditions showing water damage to surrounding building materials and insulation in the affected area.

Completed installation of customer-supplied one-piece toilet in residential bathroom. Removed existing toilet fixture, installed new wax ring seal, and properly set and secured the new toilet to the floor flange. Connected water supply line, tested for proper operation and verified no leaks at base or supply connection.

Completed installation of new Toto Drake toilet with fresh wax ring seal. Connected water supply line with braided stainless steel flex connector to ensure reliable water delivery. Verified proper bowl water level, confirmed secure mounting to floor flange, and tested flush operation for optimal performance.

Installed two customer-supplied faucets in collaboration with related job activities. Completed under-sink plumbing connections including drain assemblies, tailpieces, and flexible braided supply lines for both hot and cold water. All components were properly secured with slip nuts and fittings, ensuring leak-free operation and code-compliant installation.

Completed installation of a 50-gallon gas water heater in mechanical room, which required relocating washer and dryer to access the work area. Removed existing unstable water heater that had been improperly supported with bricks underneath. Installed new unit with proper connections including PEX supply lines, 3/4" pressure relief valve (PRV), and 1/4 turn valve for humidifier connection. All plumbing connections were secured with brass fittings, temperature and pressure relief valve assembly was properly installed and tested, and unit was commissioned to verify proper operation and safety compliance.

Technician responded to master bathroom to provide estimate for replacing existing toilet with Toto Drake model. Performed site assessment including measurements of current toilet dimensions and rough-in spacing to verify compatibility with requested fixture. Documented existing bathroom configuration, tile work, and plumbing connections to ensure proper installation specifications for estimate preparation.

Responded to a clogged bathtub drain on the second floor hallway. Upon arrival, found the tub basin with significant standing water and visible debris accumulation in the drain opening. Utilized a mechanical drain auger to clear the obstruction, successfully removing a substantial amount of organic matter, hair, and fibrous buildup from the drain line. The blockage was completely cleared, restoring proper drainage function to the fixture.

Responded to service call for kitchen sink with no water pressure. Upon inspection, diagnosed low water pressure issue at kitchen faucet. Examined under-sink plumbing configuration including garbage disposal unit, P-trap assembly, and supply line connections. Assessed existing faucet condition and water flow restrictions. Inspected all visible plumbing components beneath sink, including white PVC drainage system and connections to disposal unit. Verified proper operation of shut-off valves and checked for potential blockages or restrictions in supply lines. Documented existing plumbing configuration with cabinet-mounted components and mechanical systems for service records.

Installed a 40-gallon State brand gas water heater in commercial utility space, replacing existing unit. Connected incoming cold water supply and outgoing hot water distribution lines using copper piping with brass fittings and shutoff valves. Installed blue thermal expansion tank to protect system from pressure buildup due to thermal expansion. Secured all gas connections, verified proper venting through existing ductwork, and ensured compliance with commercial plumbing codes. Tested system operation, confirmed proper ignition, and verified no leaks at all connection points.

Completed comprehensive whole-home plumbing inspection at customer's request. Thoroughly examined all accessible plumbing systems including water supply lines, drainage systems, and mechanical room components. Inspected copper piping, PEX tubing connections with ball valve shut-offs, brass fittings, and Bradford White water heater installation. Verified proper operation of all visible plumbing fixtures, connections, and valves throughout the property. Documented current system conditions with photographic evidence showing utility room plumbing infrastructure, supply line configurations, and appliance connections. No deficiencies or immediate concerns identified during inspection; all systems functioning as designed.

Conducted site assessment of commercial men's bathroom experiencing recurring flooding issues affecting adjacent office space. Inspected existing floor drain system and documented current drain elevation relative to bathroom fixtures and floor level. Provided estimate for drain relocation and lowering to prevent water overflow and protect office areas from future flooding events.

Completed replacement of toilet fill valve and shower cartridge to restore proper fixture operation. Installed new fill valve assembly in toilet tank to address water flow issues, and replaced worn shower cartridge to eliminate temperature control problems and leaking. All connections tested and verified for proper function with no leaks detected upon completion.

Completed installation of a 50-gallon gas-fired water heater with thermal expansion tank in residential utility space. All copper supply and discharge piping was configured to manufacturer specifications with proper shutoff valves and compression fittings. The thermal expansion tank was installed on the cold water supply line to protect against thermal expansion in the closed plumbing system. All connections were pressure-tested and verified for proper operation before completing the installation.

Performed plumbing maintenance inspection on residential water heater system. Conducted internal camera inspection of water heater tank to assess sediment buildup and interior condition, and documented copper supply line connections and plumbing configuration for maintenance records.

Responded to service call for sewer line maintenance in basement. Performed cleaning of main sewer line and cut down previously installed sewer line from last year's installation to proper specifications. Accessed cleanout and completed rodding procedure to restore proper drainage flow through the system.

Responded to service call for three leaking toilets located on two levels of the residence. Inspected toilet tank components in primary bedroom on main level, identifying worn flush valve assembly and deteriorated fill valve mechanisms as sources of water leakage. Tank interior showed mineral deposits and rust-colored staining indicating age-related wear and potential seal degradation. Examined internal plumbing connections, including flush valve with cylindrical body, connecting tubes, and rubber overflow hose, as well as fill valve with float assembly and water supply connections. Documented condition of all internal mechanical components and their arrangement within tank for repair assessment.

Responded to water heater leak in basement utility area. Upon arrival, found significant water pooling on concrete floor with visible staining and moisture damage throughout the space. Inspected water heater and identified leak originating from temperature and pressure relief valve assembly. The brass valve fitting showed signs of failure, causing active water discharge onto the floor. Assessed surrounding insulation and protective covering for water damage. Documented conditions with photographs showing extent of water accumulation and compromised valve component. Provided customer with findings and recommendations for relief valve replacement to resolve the active leak and prevent further water damage to the basement floor and surrounding area.

Responded to report of toilet leaking from base during flush cycles in second-floor primary bathroom. Upon inspection, identified compromised wax ring seal between toilet base and closet flange causing water discharge during flushing. Removed toilet from floor mounting, scraped old wax ring residue from both flange and toilet horn, and installed new wax ring seal. Reinstalled toilet with proper alignment, secured closet bolts to manufacturer specifications, and tested flush cycles to confirm leak elimination and proper seal integrity.

Performed plumbing maintenance visit in utility area. Tested and verified system pressure using calibration gauge, recording reading of approximately 70-80 PSI on main line. Inspected copper and PVC piping runs in mechanical room, checking for proper installation and connections. Documented equipment condition and pipe routing with photographs for service records. All systems operational upon completion of inspection.

Responded to a kitchen drain line failure in the crawlspace area. Upon inspection, identified a deteriorated galvanized tee fitting showing significant corrosion and age-related degradation that required immediate replacement. Removed the failed galvanized tee section and repaired the drain line by installing a straight run of PVC pipe to restore proper drainage function. Work was completed in the underfloor area among existing plumbing infrastructure and wooden floor joists.